طريقة عمل بريدج بين شبكتين للميكروتك بالصور

[center]








[b][size=16][color:93bd=#000000]Remote networks
can be easily bridged using WDS feature of MikroTik RouterOS™. We will
show it for the case when the networks are connected through Atheros
wireless interface. Using EoIP, this can be extended to any other type
of interfaces, like PPTP and CISCO/Aironet. WDS works only on Prism and
Atheros based cards.
Let us assume the following network setup:
[url=http://wiki.mikrotik.com/wiki/File:Bridge.jpg][img]http://wiki.mikrotik.com/images/3/39/Bridge.jpg[/img][/url]
^^[b]Please ignore the AP; Wlan; LAN ip, all of them is not been use in this setup, photo just for reference.[/b]^^

Follow the steps below to create transparent bridge using WDS:
1. Create a bridge interface on AP and add ether1 interface to the bridge in WinBox
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_1.jpg][img]http://wiki.mikrotik.com/images/3/38/Transparently_Bridge_1.jpg[/img][/url]
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_2.jpg][img]http://wiki.mikrotik.com/images/8/88/Transparently_Bridge_2.jpg[/img][/url]
or in console
[admin@AP]> interface bridge add name=wds-bridge[admin@AP]> interface bridge port add interface=ether1 bridge=wds-bridge[b]Do the same on the Station, and add ether1, wlan1 interfaces to the bridge in Winbox[/b]
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_3.jpg][img]http://wiki.mikrotik.com/images/a/a9/Transparently_Bridge_3.jpg[/img][/url]
or in console
[admin@Station]> interface bridge add
name=wds-bridge[admin@Station]> interface bridge port add
interface=ether1 bridge=wds-bridge[admin@Station]> interface bridge
port add interface=wlan1 bridge=wds-bridge2. Make sure you have
communication between MikroTik routers, i.e., one router is configured
as server (AP), the other one as client (station). Configure wireless
interface wlan1 on AP in WinBox
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_4.jpg][img]http://wiki.mikrotik.com/images/5/57/Transparently_Bridge_4.jpg[/img][/url]
or in conslole
[admin@AP]> interface wireless set wlan1 ssid=MikroTik frequency=5805
mode=bridge disabled=noDo the same configuration on Client wireless
interface (wlan1) in Winbox
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_6.jpg][img]http://wiki.mikrotik.com/images/8/8a/Transparently_Bridge_6.jpg[/img][/url]
or in console
[admin@Station] interface wireless set wlan1 mode=station-wds
ssid=MikroTik disabled=no3. Create wds interface on AP and add the
interface to the bridge in WinBox
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_5.jpg][img]http://wiki.mikrotik.com/images/d/df/Transparently_Bridge_5.jpg[/img][/url]
or in console
[admin@AP] interface wireless set wlan1 wds-mode=dynamic
wds-default-bridge=wds-bridge4. Check whether the WDS link is
established in WinBox
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_7.jpg][img]http://wiki.mikrotik.com/images/d/d2/Transparently_Bridge_7.jpg[/img][/url]
or in console
[admin@AP] interface wireless wds> printFlags: X - disabled, R -
running, D - dynamic0 RD name="wds1" mtu=1500
mac-address=00:0B:6B:30:B4:A4 arp=enabled disable-running-check=yes
master-interface=wlan1 wds-address=00:0B:6B:35:E5:5C4. Add IP
address on AP in WinBox
[url=http://wiki.mikrotik.com/wiki/File:Transparently_Bridge_8.jpg][img]http://wiki.mikrotik.com/images/8/8d/Transparently_Bridge_8.jpg[/img][/url]
or in console
[admin@AP]> ip address add address=10.1.0.215/24 interface=wds-bridgeAnd on Station:
[admin@Station]> ip address add address=10.1.0.216/24
interface=wds-bridge5. Test the bridge by pinging from 10.0.0.215 to
10.0.0.216. Note, that the bridge needs 10...30s to learn addresses and
start passing through traffic.
NOTE: If not using NAT/MANGLE nor anything doing with conntrack, remember to turn of it at both link ends.
In the console:
[admin@xx]> ip firewall connection tracking set enabled=no
This will help you get the full bandwidth the wireless link can achive freeing the CPU load.

[/color][/size][/b][/center]